We have inventory on hand over 100000 tons ensure the steady supply of a complete range of products at competitive prices.
Technical Data | Laser Cutting | Flame Cutting | Plasma Cutting |
Effective Width of The Cutting | ≤ 4050mm | 6000mm | 3500mm |
Effective Length of The Cutting | ≤ 32000mm | 28000mm | 21000mm |
Effective Thickness of The Cutting | 2.0-22mm | - | - |
Major Equipment Brands: Italy FIMI, Italy GUIDA, Italy VIGANO, Italy NOVA, South Korea Da-hyun
Available Width | 100-2200mm | Available Thickness | 0.25-25.4mm | Available Length | 300-16500mm (Single Sheet Discharge MAX>20m) | Machinging Capacity | Thickness<10mm, Max Yield Strength≈1400Mpa Thickness 10~15mm, Max Yield Strength≈1100Mpa Thickness 16mm~25mm, Max Yield Strength≈500Mpa |
Diagonal | Length≤2000mm, Tolerance 0~1.0mm | Flatness | ≤0.1mm/2m Available to Eliminate 75% of Board Surface Defects |
Major Equipment Brands: Italy FIMI, Italy GUIDA, Italy VIGANO, South Korea Da-hyun
Slitting Width | 8-2200mm | Slitting Thickness | 0.2-18mm | Slitting Quantity | MAX 30 Pieces | Machinging Capacity | Thickness<8mm, Max Yield Strength≈1200Mpa Thickness≤10mm, Max Yield Strength≈1000Mpa Thickness 10mm~18mm, Max Yield Strength≈800Mpa |
Slitting Width Tolerance | Max 0~±0.5mm | Slitting Camber | ≤1.5mm/2000mm | Slitting Burr | Max, t<1mm:≤0.05mm Max, t ≥1mm:≤5%t |
Major Equipment Brands: Sweden Wjs, Esab, America Flow, Germany Messer,Trumpf, Japan Tanaka, Koike, Switherland Bystronic.
|
Water Jet Cutting | Laser Cutting | Plasma Cutting Machine | Flame Cutting Machine | Sawing Cutting Machine |
Maximum Cutting Thickness | 250mm | 40mm | 100mm | 500mm | 600mm |
Maximum Cutting Width | 4010mm | 4100mm | 4500mm | 8000mm | 2500mm |
Maximum Cutting Length | 12000mm | 32000mm | 25000mm | 24000mm | 8000mm |
Precision Control | ±0.8mm | ±0.02mm | ±1mm |
Major Equipment Brands: Italy IMEAS, Japan Noritake
Coil Grinding | Grinding Thickness | 0.3 - 8mm | Grinding Width | 300 - 2000mm | Grinding Roughness | 0.4 - 3.0μm | Grinding Type | NO.3 / NO.4 / HL / SB / DUPULA |
Plates Grinding | Grinding Thickness | 0.3 - 350mm | Grinding Width | 30 - 4800mm |
CNC Bending Machine
Technical Parameters | 2000t Bending Machine | 3000t Bending Machine |
Thickness | ≤60mm(length3000mm) | ≤100mm( length 3000mm) |
Length | 12500mm | 15000mm |
Major Equipment Brands: Sweden Ursviken, Italy Kuka,Gasparini, Nova,Germany Trumpf, Arku, Switherland Bystronic, Haeusler Ag, Japan Amada.
Bending | Capacity | 30-3000T | Maximum Bending Length | 15000mm | Cutting Plate | Cutting Thickness | 0.4-33mm | Cutting Length | 100-6050mm | Anti-Distortion (Width:Thickness) |
5:1 |
Circling | Width | Max 5000mm | Coil Thickness | Max 200mm | Correct Flat | Machining Width | 100-2650mm | Machining Thickness | 1-60mm | Flatness | 0.5mm/1m |
Plasma Welding, Strip Electrode Surfacing Welding, Argon Arc Welding, Tig Welding, Laser Welding, Manual Arc Welding, Submerged Arc Welding Equipment Cluster
Main Equipment Brands: German Trumpf, German Kuka, American Lincoln, Swedish Esab, French Saffron, Japanese Kawasaki and Panasonic.
H-Shaped Steel Production Line
Technical Data of Straightening Machine | |
Flange Width | 200-800mm |
Flange Thickness | 6-40mm |
Minimum Web Height | 200mm |
Technical Data of Door-type SAW | |
Suitable for The Width of H Beam | 200-800mm |
Suitable for Length of H Beam | 2000-15000mm |
Suitable for Height of H Beam | 200-1500mm |
Technical Data of Assembly Machine | |
Flange Width | 150-800mm |
Thickness | 6-60mm |
Web Height | 200-2000mm |
Strip Overlay Welding Machine
Technical Data of Strip Overlay Welding Machine | |
Dia | 8000mm |
Weight | 100t |
Plasma Welding Machine
Technical Data | |
Weld Length | ≤12500mm |
Plate Butt Thickness | 1-10mm |
Technical Parameters | INNSE Italy | DAE-YANG South Korea |
X-axis, Y-axis, Z-axis | 6000 4500 1100mm | 4000 3000 1000mm |
Boring Diameter | ≤Φ60mm | Φ16-Φ80mm |
Processing Depth | ≤1000mm | ≤1000mm |
Technical Parameters | INNSE Italy | Shenyang Machine Tool GDC60130MD, GDC3070MD | DAE-YANG South Korea | |
X-axis, Y-axis, Z-axis | 8000 4500 1000mm | 13000 6000 500mm | 7000 3000 500mm | 6000 6000 800mm |
Boring Diameter | ≤Φ120mm | ≤Φ100mm | ≤Φ100mm | Φ2 -Φ 100mm |
Processing Depth | ≤420mm | ≤300mm | ≤200mm | ≤400mm |
Technical Parameters of Bending Machine | FACCN (Three Rollers) | SERTOM (Four Rollers) | HAEUSLER |
Width | 3200mm | 4100mm | 4250mm |
Thickness | 110/90mm | 50mm | 210mm |
Technical Data | Wuzhong Double Column | Wuzhong Double Column | Schess | |
Height | 5000mm | 6000mm | 6500mm | 3000mm |
Load Bearing | 160t | 400t | 600t | 50t |
Table Diameter | Φ7200mm | Φ10000mm | Φ10000mm | Φ3500mm |
Max. machining Diameter | Φ8000mm | Φ12500mm | Φ22000mm | Φ4000mm |
Simultaneous | 3-Axis Simultaneous Motion | 3-Axis Simultaneous Motion | 3-Axis Simultaneous Motion | 5-Axis Simultaneous Motion |
Major Equipment Brands: Germany Schiess, Italy Innse-Berardi, Pama, Japan Mitsubishi, Okuma, Korea Daeyang
Maximum Machining Height | Width Between Columns | Maximum Machining Length | |||
Gantry Machining Center | 7000mm | 8000mm | 50000mm | ||
X Axial | Y Axial | Z+W Axial | Maximum Load Bearing | Boring Blade Diameter | |
Floor-Type Boring and Milling Machine | 25700mm | 8000mm | (1800+2000)mm | 250T | ∅280mm |
Height | Load Bearing | Maximum Machining Diameter | |||
Turning and Milling Machine | 6500mm | 600T | ∅22000mm | ||
Vertical Lathe | 4000mm | 50T | ∅5000mm | ||
X Axial | Y Axial | Z Axial | Drilling Capacity | Working Depth | |
Deep-Hole Drilling Machine | 6000mm | 4500mm | 1100mm | ∅16-80mm | ≤1000mm |
Multi-Hole Drilling Machine | 13000mm | 6000mm | 1000mm | ∅2-120mm | ≤420mm |
If you need, please fill in the form below carefully and we will get in touch with you in time.
If you have any questions about our products, please feel free to contact us. We will reply very soon.
ength and anti-oxidant properties, have higher durable plastic. The production process is relatively simple, and good weldability, but normalizing cooling rate sensitive._GB/T 3077 12Cr1MoV Chemical Composition:__ _ Grade_ The Element Max (%)_ _ _ C_ Si_ Mn_ P_ S_ _ _ 12Cr1MoV_ 0.08~0.15_ 0.17~0.37_ 0.40~0.70_ 0.035_ 0.035_ __GB/T 3077 12Cr1MoV Mechanical Property:__ _ Grade_ 12Cr1MoV Mechanical Property_ _ _ Thickness_ Yield_ Tensile_ HB_ _ _ 12Cr1MoV_ mm_ Min Mpa_ Mpa_ HB_ _ _ 6-50_ 245_ 490_ _ _ _ 50-200_ 245_ 490_ _ __GB/T 3077 12Cr1MoV covers the following issues of hot rolled and forging alloy steel: the dimension, shape, weight, tolerance, engineering specification, test method, inspection rules, packaging, marking, and quality certificates._
Read moreance is very good._The 15CrMo-series Pearlite-heat-resisting steels have high thermal strength (Δb≥440mpa) and anti-oxidation at high temperature, and have certain capability of resisting hydrogen corrosion. Because of the high content of CR, C and other alloying elements in steel, the hardening tendency of steel is obvious and the weld ability is poor._15CrMo steel chemical composition:__ _ Grade_ 15CrMo steel chemical composition (mass fraction) ( % )_ _ _ _ C_ Mn_ Si_ Cr_ Mo_ Ni_ Nb + Ta_ S_ P_ _ _ 15CrMo_ 0.12 ~ 0.18_ 0.40 ~ 0.70_ 0.17 ~ 0.37_ 0.80 ~ 1.10_ 0.40 ~ 0.55_ ≤0.30_ __ ≤0.035_ ≤0.035_ __15CrMo mechanical properties of steel_
Read morealloy chromium, molybdenum, nickel case hardening steel. Oil Quenched & Tempered Hardness is 28-34 HR c. GB 20Cr steel Annealing delivery hardness less than 250HB.20Cr with a lower carbon content range, So GB 20Cr alloy steel have good weld ability._GB/T 3077 20CR Chemical composition:__ _ C(%)_ 0.18~0.24_ Si(%)_ 0.17~0.37_ Mn(%)_ P(%)_ _ _ S(%)_ ≤0.030_ Cr(%)_ 0.70~1.10_ 0.50~0.80_ ≤0.030 _ __GB/T 3077 20CR alloy steel mechanical property:__ _ Tensile Strength (σb/MPa)_ Yield point (σs/MPa)_ Elongation (δ5/%)_ Reduction of Area (ψ/%)_ Impact Absorbing Energy(Aku2/J)_ Brinell Hardness(HBS100/3000)_ _ _ Annealing or High Tempering_ _ _ ≥835_ ≥540_ ≥10_ ≥40_ ≥47_ ≤179_ __GB/T 3077 20CR steel application:_ 20CR steel is mainly used for making cam shaft, driven gears of small tractor. This kind of steel also is mostly used in the manufacturing of the high demand heart intensity, surface under wear, section under 30 mm or complex and not big load carburized parts (oil quenching), such as: machine tool transmission gear, gear shaft, worm and piston pins, claw clutch, etc._
Read moreCrMo Chemical Composition_ _ _ Grade_ The Element Max (%)_ _ _ C_ Si_ Mn_ P_ S_ _ _ 30CrMo_ 0.26~0.34_ 0.17~0.37_ 0.40~0.70_ 0.035_ 0.035_ __30CrMo alloy steel plate Mechanical Property: __ _ Grade_ _ 30CrMo Mechanical Property_ _ _ Thickness_ Yield_ Tensile_ HB_ _ _ 30CrMo_ mm_ Min Mpa_ Mpa_ HB_ _ _ 6-50_ 785_ 930_ _ _ _ 50-200_ 785_ 930_ _ __GB/T 3077 30CrMo covers the following issues of hot rolled and forging alloy steel: the dimension, shape, weight, tolerance, engineering specification, test method, inspection rules, packaging, marking, and quality certificates.__ The standard applies to alloy structural steel bar 250mm maximum diameter or thickness. After consultation between the two sides of supply and demand, bar stock of diameter greater than 250 mm can also be provided.__
Read moreis good. The working temperature is up to 500 ° C, the low temperature can be -100 ° C, and has high static strength and high fatigue strength, good hardenability, no tendency to overheat, small quenching deformation, and moderate machinability. However, this material has a first type of temper brittleness, and the weldability is not good. It needs to be preheated to 150-400 ° C before welding, and heat treatment is needed after welding to eliminate stress. Generally used after quenching and tempering treatment._35CrMo Steel Chemical Composition (%):__ _ Steel Grade_ C_ Si_ Mn_ P_ S_ Cr_ Mo_ Cu_ _ _ 35CrMo_ 0.32 to 0.40_ 0.17 to 0.37_ 0.40 to 0.70_ ≤ 0.030_ ≤ 0.030_ 0.80 to 1.10_ 0.15 to 0.25_ ≤ 0.30_ __35CrMo Alloy Steel Mechanical Properties:__ _ Grade_ Thickness_ Yield_ Tensile_ _ _ 35CrMo_ mm_ Min Mpa_ Mpa_ _ _ 6-50_ 835_ 980_ _ _ 50-200_ 835_ 980_ __Applications of 35CrMo Alloy Steel:_ 35CrMo alloy steel can be used to manufacture major parts in various machines that withstand impact, bending and high loads, such as rolling mill gears, crankshafts, connecting rods, fasteners, automotive engine spindles, axles, engine transmission parts, large motor shafts, bolts for boilers with operating temperatures below 400 °C, nuts below 510 °C, high pressure seamless thick-walled conduits for chemical machinery (450-500 ° C, non-corrosive media)._Equivalent:_ 35CrMo equivalent to US ASTM, European Germany DIN EN, British BS EN, France NF EN, Japanese JIS, and ISO standard._
Read morem-60mm_ Length: 5.8m 6m 9m 12m_40Cr Steel Chemical Composition:__ _ Grade_ C _ Si _ Mn _ S _ P _ Cr _ Ni _ Cu _ Mo _ _ _ 40Cr _ 0.37-0.44 _ 0.17-0.37 _ 0.50-0.80 _ ≤0.035 _ ≤0.035 _ 0.80-1.10 _ ≤0.30 _ ≤0.30 _ ≤0.15 _ __40Cr Steel Application: _ Used in making gear, the sleeve, spindle, crankshaft, spindles, pins, rods, screws, nuts, inlet valve.__
Read more0.38~0.25_ Si(%)_ ≤0.40_ Mn(%)_ 0.60~0.90_ P(%)_ ≤0.035_ _ _ S(%)_ ≤0.035_ Cr(%)_ 0.90~1.20_ Mo(%)_ 0.15~0.30_ _ _ _ __42CrMo Mechanical Property: __ _ Grade_ Thickness_ Yield_ Tensile_ HB_ _ _ 42CrMo_ mm_ Min Mpa_ Mpa_ HB_ _ _ 6-50_ 930_ 1080_ _ _ _ 50-200_ 930_ 1080_ _ __GB T-3077 42CRMO standard applies to manufacture of bearing ring steel pipe rolling elements made by high-carbon chromium bearing steel processed with hot rolled forged round, steel wire, cold rolled.__
Read moreenum._50CrMo4 steel with a particular composition are dedicated for vehicles and machines that require high hardness and are subject to strong bending, twisting, abrasion and wear loads._Chemical composition (%) of steel 50CrMo4:__ _ C_ Si _ Mn _ P _ S _ Cr _ Mo _ _ _ 0.46 - 0.54 _ max 0.4 _ 0.5 - 0.8 _ max 0.025 _ max 0.035 _ 0.9 - 1.2 _ 0.15 - 0.3 _ __GB/T 3077 50CrMo4 Mechanical properties:__ _ Yield_ Rp0.2 (MPa)_ Tensile_ Rm (MPa)_ Impact_ KV/Ku (J)_ Elongation_ A (%)_ _ _ 182 (≥)_ 769 (≥)_ 44_ 32_ __GB/T 3077 50CrMo4 steel application:_ 50CrMo4 steel is used as semi-finished products for the manufacture of components such as crankshafts, cogwheels, heavy-duty axles, gears, valves, heavy-duty screws, thrust rollers, guides, articulated joints, thrust rings, bolts or bushes.__
Read moren._EN 10083-3 51CrV4 Chemical Composition (%):__ _ C_ Si _ Mn _ P _ S _ Cr _ V _ _ _ 0.47 - 0.55 _ max 0.4 _ 0.7 - 1.1 _ max 0.025 _ max 0.025 _ 0.9 - 1.2 _ 0.1 - 0.25 _ __EN 10083-3 51CrV4 Mechanical Property:__ _ _ Grade _ Mechanical Property_ _ _ _ Yield Strength(MPa)_ Tensile Strength(MPa)_ % Elongation min_ _ _ EN10083-3 51CrV4_ 900_ 1100-1300_ 12_ __Additional Condition:_ UT (Ultrasonic examination),AR(As Hot Rolled only),TMCP(Thermal Mechanical Control Processing),N(Normalized),Q+T(Quenched and Tempered),Z Direction Test(Z15,Z25,Z35) ,Charpy V-Notch Impact Test, HIC test, NDT ,PWHT( Simulated Post Weld Heat Treatment),NACE0175,The Third Party Test (Such as SGS Test), Coated or Shot Blasting and Painting.__
Read moreEmail: [email protected] Copyright 2022 Steel Iron & Steel Co., Ltd . All Rights Reserved.